How to Install a Waste Drawer Liner. 1- Remove the old bag. 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app. (For wi-fi model) Note: Steps 4 and 5 must be done in that order according to the manufacturer’s instructions.1- Remove the old bag. 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app. (For wi-fi model) Note: Steps 4 and 5 must be done in that order according to the manufacturer’s instructions.Hello @Mariagav , Thank you for your reply. According to your order number, the robot is no longer under warranty. If the cleaning of the DFI sensor didn’t fix the issue, we recommend replacing it so you can order a new one from this link: We also recommend replacing the 3 sets of pins so you can order new ones from these links: The following …We understand how confusing this could be, but actually the connect version of the Litter-Robot uses a new model of the DFI sensor that only has one not two lenses as the older model. However, the constant blue LED blinking indicates an issue with the DFI sensor so we recommend you to go through this troubleshooting here:Hello, I have basically the same problem with my litter robot 3 connect. I have tried everything within the trouble shooting like the person said above, I’ve only had it for 1 week. As well I’ve tried to level out the floor for the sensor. But the main problem I am having is the connect only connected to the app successfully for 3 days. And then any …The DFI repair is actually quite easy to do. You can purchase a replacement DFI from HERE for $30. You can watch this how to VIDEO on how to replace the DFI. The tools needed for this repair are a #2 Philips screwdriver with at least a 6 inch long shank, and needle nose pliers for convenience.DFI Boards to the Base. 3 Figure 10 Figure 12 Figure 9 Figure 11 Figure 13. INSTALL NEW DFI BOARD ASSEMBLY 15. On the front edge of the opening, free the gray ... 1-877-250-7729 or [email protected] LR3-8051-0a. Title: LR3-8051-0a_gr - Installation Guide - DFI.indd Author: mhannaDetails. Stop scooping today and give your cat clean litter every time they go with the Litter-Robot 3, the highest-rated automatic, self-cleaning litter box. Purchase includes a 90-day in-home trial, comprehensive coverage with our WhiskerCare™ 1-Year Warranty, and free shipping (excl. AK, HI, PR). Never scoop again®.How to Install a Waste Drawer Liner. 1- Remove the old bag. 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app. (For wi-fi model) Note: Steps 4 and 5 must be done in that order according to the manufacturer’s instructions.Thoroughly clean the DFI sensor lens and the surrounding area with a clean, dry cloth. Sensors may be obstructed by debris or dust, which can cause detection problems. ... Description Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 only The Litter-Robot …How to Install a Waste Drawer Liner. 1- Remove the old bag. 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app. (For wi-fi model) Note: Steps 4 and 5 must be done in that order according to the manufacturer’s instructions.We understand how confusing this could be, but actually the connect version of the Litter-Robot uses a new model of the DFI sensor that only has one not two lenses as the older model. However, the constant blue LED blinking indicates an issue with the DFI sensor so we recommend you to go through this troubleshooting here:Litter Robot 3 not reversing during cycle. My Litter Robot 3 has been having a weird issue for the last two weeks. When it cycles, the globe rotates counter-clockwise until the hall sensor detects the magnet on the globe. It then stops, like it should. Then it's supposed to rotable clockwise to return to its home position, when the hall sensor ...Note: This problem is EXACTLY the same as this other post I found, which is why I’ve essentially just copied the description from there: Litter Robot Cannot Find Dump Position. Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again; cleaning the …Out little robot has a continuous yellow /amber cycling light and the control panel is totally unresponsive. Things we have tried: Cleaning the pinch sensors Checking the spring sensor Powering off and on (via plug as power button not responsive) Checking for control panel lockout Checked back clips are in Checked globe is locked at the back.Purchase replacement pinch contact and drawer full indicator (DFI) circuit board assembly for your Litter-Robot 3. ... (DFI) circuit boards for your Litter-Robot 3. Contact Whisker Support if your robot is still under warranty The store will not work correctly in the case when cookies are disabled.Litter-Robot 3 Pinch Contact. $5. Buy in monthly payments with Affirm on orders over $50. Learn more. If your Litter-Robot 3 is no longer under warranty, you can purchase this replacement pinch contact.Tamia December 5, 2019, 9:41pm 1. Hello, I have a problem with Litter Robot 3. It has blue flashing light at the beginning. I have tried everything (cleaning, reset, check dfi sensor and empty drawer) and when I plug back in it stuck at solid yellow light now (yellow light only). None of buttons is worked even the power button.Note: This problem is EXACTLY the same as this other post I found, which is why I’ve essentially just copied the description from there: Litter Robot Cannot Find Dump Position. Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again; cleaning the …Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation Litter-Robot 29.1K subscribers 46K views 1 year ago How to install a replacement DFI Kit + Pinch …3. Place treats on the step or around the Litter-Robot so your cat associates rewards with the unit. 4. Since cats are curious and love to go into boxes, try putting the original packaging over the Litter-Robot with a hole cut out for the entryway and drawer. 5. Once you notice that your cats have used the Litter-Robot, pow-Litter Robot owner here -- Have had two litter robots and I think a recent batch of circuits is faulty. First one had no trouble with DFI for years; second one I bought refurbished and DFI went in 2 months. I replaced the DFI on first one, that lasted only 2 months. If Whisker does not get on top of this, they will lose their audience.Litter robot 3 yellow light flashing rapidly . I've followed the troubleshooting steps such as: Removing everything from the base, depressing the pinch sensor 10 times, cleaning the terminals and ... and the recommendation was to spend $30 + shipping on a new DFI assembly. The above-linked post fixed the issue in 30 seconds and ...Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • goat-anus-milk ... If bought after Jan 1 2020 and out of warrenty I belive you can get a free dfi sensor kit replacement, if not it is like $30 for a replacement sensor kit. If you can’t fix it and it’s under warrently they will ...The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. ... DFI sensor issue. DFI sensor needs replacing; Replacement Guide (H) YELLOW SOLID: Cycling (In use) Working normally; Without rotation DFI …3. Place treats on the step or around the Litter-Robot so your cat associates rewards with the unit. 4. Since cats are curious and love to go into boxes, try putting the original packaging over the Litter-Robot with a hole cut out for the entryway and drawer. 5. Once you notice that your cats have used the Litter-Robot, pow-To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. 1 Like. Litter Robot Connect - dumping clean litter and indicating full tray erroneously. Perpetuus December 22, 2019, 1:03am 3. Thanks for the reply. ...Hi all, I'm having an issue with my 1 year old litter robot 3 where after every use the app says drawer full and the blue light flashes. I've followed all the litter robot troubleshooting steps including cleaning the lense and re-calibrating the sensor. I've created two support tickets and have been waiting over two weeks for a response from ...Hi! I’ve installed a new DFI sensor and circuit-board for the Litter Robot 3 to upgrade to Litter Robot 3 Connect as the DFI sensor on our LR3 had gone faulty and was no longer reporting an accurate level in the waste drawer. On re-assembling the unit, the orange light is flashing slowly, about once per second. I’ve checked that this is not …Litter robot 3 yellow light flashing rapidly . I've followed the troubleshooting steps such as: Removing everything from the base, depressing the pinch sensor 10 times, cleaning the terminals and ... and the recommendation was to spend $30 + shipping on a new DFI assembly. The above-linked post fixed the issue in 30 seconds and ...After some research I decided it was probably a bad DFI or contact (they were gross). So, now that I've installed a brand new DFI sensor & contact pins, I'm still seeing yellow blinking at a 1 sec interval cadence. I've checked to make sure that the bonnet and connectors are attached. Already spent hours trying to get this thing to work.The updated DFI Kit is pictured on the bo om. 8-inch #2 Phillips screwdriver (20.3 cm) Preparation: 1 Press the Power bu on to turn the unit o and unplug it from the wall. …Hello, I have a problem with Litter Robot 3. It has blue flashing light at the beginning. I have tried everything (cleaning, reset, check dfi sensor and empty drawer) and when I plug back in it stuck at solid yellow light now (yellow light only). None of buttons is worked even the power button. Any help would be appreciatedHi all, I’ve been trying to troubleshoot my litter robot 3 for a while and the agent is always offline on the app so I can’t get any help on fixing it. My red light for cat timing does not come on and it will not cycle unless I press the button. I replaced the DFI sensors a few month back but I don’t think that’s the problem.1. Turn the base over so it is upside down. 2. Remove the 9 screws connecting the bottom of the base to the top of the base. 1 screw at the back of the unit behind the black cat sensor foot. 3. Gently lift to separate the two halves of the base. The pieces will …To troubleshoot the blue blinking, let’s start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base. 2.) Wait 10 seconds then plug the unit back in. 3.) Allow the unit to complete a start‐up cycle.To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes it resets it back to solid but every time now after my unit cycles it continues to ...The issue that you are having would require replacing the DFI sensor and the 3 sets of pins so you can order the following parts from the following links: RobotShop Europe Litter-Robot 3 Open Air DFI Hardware (v2) Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 ...http://www.litter-robot.com/ The Main Circuit Board is the brains of the operations. This replacement is for customers whose Litter-Robot is out of warranty,...Also I'd like to mention I have the original litter robot 3 that didn't come with connect. But I did install that a year later. I had issues when I first got mine and I thought it was the dfi sensor but just ended up I had to take out the "key" that's in the back and I think there was a cover that was unnecessary too on the inside.I have completely cleaned it inside and out, nothing on the lenses. Robot Litter 3 Troubleshooting steps already taken: Cleaned/on-off /reset Additional information: #676303 (Web #1300025071 Ordered on 3/12/2018 ) Thank you so much in advance for your help! ... This issue indicates a defective DFI sensor and it needs to be replaced.Nov 18, 2019 · I receive really interesting update from Litter-Robot. To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. Litter Robot owner here -- Have had two litter robots and I think a recent batch of circuits is faulty. First one had no trouble with DFI for years; second one I bought refurbished and DFI went in 2 months. I replaced the DFI on first one, that lasted only 2 months. If Whisker does not get on top of this, they will lose their audience.How to install a replacement DFI Sensor Kit and Pinch Detector Terminals in the Litter-Robot III Open Air.Hi, litter robot 3 connect blue flashing light (fast flashing). Have taken the robot apart a few times, cleaned the sensors. ... 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app.The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second. This will also occur if the cat sensor is activated by a cat entering the globe.Litter Robot owner here -- Have had two litter robots and I think a recent batch of circuits is faulty. First one had no trouble with DFI for years; second one I bought refurbished and DFI went in 2 months. I replaced the DFI on first one, that lasted only 2 months. If Whisker does not get on top of this, they will lose their audience.To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes ...Removing the bonnet, flexing/bending back the latches (I discovered I wasn't properly seating the back clasps in-place, this helped a bit with the jerky spinning but failed to avoid the pinch detect fault) Emptied the tray, ensured the bag was installed properly. Emptied the litter entirely and replaced to ensure it's below the fill line.So one day, out of the blue, the same issue happened with our Open Air III, all 3 lights blinking and nothing works. What happens is that after restart the yellow light …The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. ... DFI sensor issue. DFI sensor needs replacing; Replacement Guide (H) YELLOW SOLID: Cycling (In use) Working normally; Without rotation DFI …Litter-Robot 3 is made with standard plastics and the liner is made out of PVC. ... Debris may cause the DFI to indicate a full drawer regardless of the waste in the drawer. ... This will ensure that the automated Cat Sensor is ready for your cat's next visit. Purchase Whisker Cleaner Wipes.Thoroughly clean the DFI sensor lens and the surrounding area with a clean, dry cloth. Sensors may be obstructed by debris or dust, which can cause detection problems. ... Description Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 only The Litter-Robot …Also I'd like to mention I have the original litter robot 3 that didn't come with connect. But I did install that a year later. I had issues when I first got mine and I thought it was the dfi sensor but just ended up I had to take out the "key" that's in the back and I think there was a cover that was unnecessary too on the inside.1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container.Purchased to repair my Litter robot 3 the service received was excellent and the part arrived on the Monday after ordering on the Friday. Geniene Gordon . 01/02/2024 . ... We had to install the new DFI sensors the day we were leaving for a week away, so the time pressure was massive. Mary was extremely helpful by replying to my emails ...Litter Robot owner here -- Have had two litter robots and I think a recent batch of circuits is faulty. First one had no trouble with DFI for years; second one I bought refurbished and DFI went in 2 months. I replaced the DFI on first one, that lasted only 2 months. If Whisker does not get on top of this, they will lose their audience.Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards here, or if your Litter-Robot is under warranty, log in to your …Details. Stop scooping today and give your cat clean litter every time they go with the Litter-Robot 3, the highest-rated automatic, self-cleaning litter box. Purchase includes a 90-day in-home trial, comprehensive coverage with our WhiskerCare™ 1-Year Warranty, and free shipping (excl. AK, HI, PR). Never scoop again®.Hi! I’ve installed a new DFI sensor and circuit-board for the Litter Robot 3 to upgrade to Litter Robot 3 Connect as the DFI sensor on our LR3 had gone faulty and was no longer reporting an accurate level in the waste drawer. On re-assembling the unit, the orange light is flashing slowly, about once per second. I’ve checked that this is not …Nov 18, 2019 · I receive really interesting update from Litter-Robot. To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. Our litter robot 3 has been barely working for a while. I'd have to hit reset and cycle for it to actually work. Well, about 2 weeks ago it over rotated during a cycle and became "stuck" (wouldn't rotate back into starting position). Putting it back manually caused a yellow flashing light that wouldn't go away.Hi, litter robot 3 connect blue flashing light (fast flashing). Have taken the robot apart a few times, cleaned the sensors. ... 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app.Litter Robot Connect version has a new type of DFI sensor based on laser so it has only one circuit board. Old DFI sensor was based on IR light so it had two circuit boards. ... To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light.LED blue flashing quicker than when the drawer is full and no button of the control panel is working. What should I do? Replace the draw sensors as mentioned in the coments?In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how to replace these parts: 1- Shipping address. 2- Phone number. 3- Serial number located on the back of the robot.Our litter robot 3 has been barely working for a while. I'd have to hit reset and cycle for it to actually work. Well, about 2 weeks ago it over rotated during a cycle and became "stuck" (wouldn't rotate back into starting position). Putting it back manually caused a yellow flashing light that wouldn't go away.In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how to replace these parts: 1- Shipping address. 2- Phone number. 3- Serial number located on the back of the robot.Then, after a minute, go into the Litter Robot driver, refresh, and see if the Cycles After Drawer Full (a counter in the Litter Robot that counts cycles after DFI IR sensor indicates a full drawer) count goes to 0. It’s supposed to go to 0 along with the cycle count when a reset is done.May 23, 2021 · How to install a replacement DFI Sensor Kit and Pinch Detector Terminals in the Litter-Robot III Open Air. To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes ...Follow the video except that instead of replacing the sensor just take one of the pinch terminals and plug the wires you disconnected into each end of it. Maybe wrap the whole thing in some electrical tape after you are done, then re-assemble. 1. [deleted]After some research I decided it was probably a bad DFI or contact (they were gross). So, now that I've installed a brand new DFI sensor & contact pins, I'm still seeing yellow blinking at a 1 sec interval cadence. I've checked to make sure that the bonnet and connectors are attached. Already spent hours trying to get this thing to work.In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how …Out little robot has a continuous yellow /amber cycling light and the control panel is totally unresponsive. Things we have tried: Cleaning the pinch sensors Checking the spring sensor Powering off and on (via plug as power button not responsive) Checking for control panel lockout Checked back clips are in Checked globe is locked at the back.Litter Robot owner here -- Have had two litter robots and I think a recent batch of circuits is faulty. First one had no trouble with DFI for years; second one I bought refurbished and DFI went in 2 months. I replaced the DFI on first one, that lasted only 2 months. If Whisker does not get on top of this, they will lose their audience.We understand how confusing this could be, but actually the connect version of the Litter-Robot uses a new model of the DFI sensor that only has one not two lenses as the older model. However, the constant blue LED blinking indicates an issue with the DFI sensor so we recommend you to go through this troubleshooting here:1 / 2. So my litter robot 3 won’t cycle and it is flashing yellow rapidly which I understand is the anti-pinch sensor. I’ve heard of the tin foil hack and may need to resort to it but I worry without the sensor it could cycle while the cats are in there. Not sure iof that is a realistic possibility or not….. Regardless, i read about the ...The Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the Waste Drawer that check if the drawer is full each time the Globe returns to the Home position. In the event you need to replace your DFI sensors, please follow these instructions. Kit includes: Drawer Full Indicator board assembly (2) retainersTamia December 5, 2019, 9:41pm 1. Hello, I have a problem with Litter Robot 3. It has blue flashing light at the beginning. I have tried everything (cleaning, reset, check dfi sensor and empty drawer) and when I plug back in it stuck at solid yellow light now (yellow light only). None of buttons is worked even the power button.Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again. cleaning the unit. slightly opening the pin in the power jack. making sure that it is plugged directly into the wall using its original power adaptor.Apr 19, 2021 · r/litterrobot • 3 yr. ago DRob433 LR3 DFI & Pinch Sensor - Preventing Errors? Tips & Tricks Our family has had our LR3 for two years and are mostly in love with it. However, we've had another set of DFI & Pinch Sensors go bad this past week (our 2nd in the last year), which has me concerned about long-term viability of the unit. My litter robot 3 had been flashing blue light and then yellow light (very fast) after pressing the reset button. I’ve read some troubleshooting to check for the metal pinch bars to be in contact all the time. I’ve tried to clean it and it appears to be in contact as well. ... In this case, the DFI sensor needs to be replaced.To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. 1 Like. Litter Robot Connect - dumping clean litter and indicating full tray erroneously. Perpetuus December 22, 2019, 1:03am 3. Thanks for the reply. ...The Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. Omnisense™ also supports the SafeCat system which continuously analyzes 4 safety zones to ensure your cat is always safe. There are 3 laser sensors located in the top of the bezel ...May 23, 2021 · How to install a replacement DFI Sensor Kit and Pinch Detector Terminals in the Litter-Robot III Open Air. After some research I decided it was probably a bad DFI or contact (they were gross). So, now that I've installed a brand new DFI sensor & contact pins, I'm still seeing yellow blinking at a 1 sec interval cadence. I've checked to make sure that the bonnet and connectors are attached. Already spent hours trying to get this thing to work.In this case, the DFI sensor and the 3 sets of pins will need to be replaced so we will send you new ones under the warranty. The following videos will show you how to replace these parts: 1- Shipping address. 2- Phone number. 3- Serial number located on the back of the robot.http://www.litter-robot.com/ The Main Circuit Board is the brains of the operations. This replacement is for customers whose Litter-Robot is out of warranty,...Upgrade your Litter-Robot 3 to Connect to get all the perks of the app with this do-it-yourself installation kit! With a WiFi-enabled Litter-Robot, you can use our app to: View the waste drawer level. Change settings remotely. Receive status notifications. Monitor your cat's litter box usage. Control multiple Whisker robots.Hello, I have basically the same problem with my litter robot 3 connect. I have tried everything within the trouble shooting like the person said above, I’ve only had it for 1 week. As well I’ve tried to level out the floor for the sensor. But the main problem I am having is the connect only connected to the app successfully for 3 days. And then any …. The Litter-Robot 3 is equipped with infrared The Litter-Robot four-part system (base, globe, bonnet, and drawer) wa 1. Turn the base over so it is upside down. 2. Remove the 9 screws connecting the bottom of the base to the top of the base. 1 screw at the back of the unit behind the black cat sensor foot. 3. Gently lift to separate the two halves of the base. The pieces will … How to replace your Litter-Robot's Cat Sensor. Posted Hi, litter robot 3 connect blue flashing light (fast flashing). Have taken the robot apart a few times, cleaned the sensors. ... 2- Wipe the DFI sensor’s circuit boards on each side. 3- Install the new bag. 4- Press the “Reset” button on the robot. 5- Reset the level on the app.I concluded (before disassembly) that it was both the pinch sensor and the DFI assemble causing me trouble so in a Hail Mary I tried to fix both problems in one go. On my litter robot I found and removed 9 screws from the underside of the base to access the electronics within the base. To reset DFI sensor fault on a Connect Litter Robot p...
Continue Reading